Zapi AC-2 Instrukcja Obsługi Pobierz pdf (Strona 105)

105

- 15/18/20BT-7, 16/18/20B-7 Traction Master (03) Setup.

Code

ADJUSTMENTS

(Service

level)

245

SET POT BRK MIN

246

SET POT BRK MAX

145

SET BATTERY TYPE

140

ADJUST BATTERY

249

MAX STEER RIGHT

243

MAX STEER LEFT

152

SET STEER 0-POS.

246

SET STEER RIGHT

241

SET STEER LEFT

249

THROTTLE 0 ZONE

252

THROTTLE X POINT

253

THROTTLE Y POINT

248

ADJUSTMENT#2 BDI

249

ADJUSTMENT#1 BDI

157

ADJUSTMENT#3

251

MAIN CONT. VOLT.

252

AUX OUTPUT VOLT.

156

ADJUSTMENT#4

242

SPEED FACTOR

This parameters adjusts the Electric brake coil voltage (PWM output C28).

This parameter determines the motor temperature level at which the “Motor temperature” alarm is

signalled. The range is from 0 °C to 200 °C with 1 °Csteps. This parameter must be adjusted only if the

“Set temperature” (menu“Set option”) parameter is programmed “Analog”.

Speed Factor = (88 * rr * p) / Ø Where: rr = total gearbox reduction ratio, p = number of pair pole of the

motor (2), Ø = traction wheel diameter expressed in centimeters (cm)

It adjusts the lower level of the no-load battery discharge table. See also Dual ac2 manual

It adjusts the upper level of the no-load battery discharge table. See also Dual ac2 manual

At each key-off battery charge is stored. At each key on the battery voltage is read and the battery

charge is estimated. The battery charge is updated only if the new estimated battery charge differs from

the stored one by the ADJUSTMENT #3 set %.

This parameters adjusts the Line contactor coil voltage (PWM output C26).

This parameter sets the max steering angle in left direction.

Deadband in the accelerator input curve (see also curve in the dual ac2 manual).

This parameter changes the characteristic of the accelerator input curve.

Steering poti output voltage when the wheels are fully turned right (maximum of the steering poti range).

Steering poti output voltage when the wheels are fully turned left (minimum of the steeringpoti range).

Steering poti output voltage when the wheels are straight

This parameter sets the max steering angle in right direction.

It records the minimum value of braking pedal potentiometer when the braking pedal switch is closed;

the procedure is similar to the "Program Vacc" function (see chapter 9.3 of the manual). This procedure

must be carried out only if the "Pedal braking" option is programmed as "Analog".

It records the maximum value of braking pedal potentiometer when the braking pedal is fully pressed;

the procedure is similar to the "Program Vacc" function (see chapter 9.3). This procedure must be carried

out only if the "Pedal braking" option is programmed as "Analog".

Nominal battery voltage.

Fine adjustment of the battery voltage measured by the controller (ZAPI production line adjusted).

0.9 V

20%

36V

63%

25%

LEVEL = 3

0.9V

2.7V

90 ˚(3W) / 97 ˚(4W)

90 ˚(3W) / 75 ˚(4W)

9.0 V

48 V

51.40 V

4.4V

145 ˚

Parameter explanation.

Values

1 2 ... 100 101 102 103 104 105 106 107 108 109 110 ... 145 146

Komentarze do niniejszej Instrukcji

Brak uwag

Zapi AC-2 Instrukcja Obsługi Strona 105

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Zasilacze i falowniki Zapi AC-2